Setting Up Pairing The Star Tsp100 Lan For Mac
Star TSP 100 LAN Setup for Mac This guide provides step-by-step instructions on how to install a Star TSP143LAN for Mac Device checklist: In order to set up your receipt printer with your Mac you'll first need to make sure you have all the peripherals needed. Cables: You will need a power cable for the printer and an ethernet cable to plug the printer in to your internet router. If you don't already have an ethernet cable ask your printer supplier to include one when you buy the printer or pick one up from your local electronics store. Receipt Rolls: Make sure you've got some 80mm receipt rolls ready to go. To load your receipt roll open the latch on the top right of the printer, place the roll inside and pull some of the paper through before closing the lid. Cash Drawer (Optional): You may also wish to set up your cash drawer at the same time, to do this you'll need a specialised cash drawer cable. This is similar looking to an ethernet cable but is smaller on one end.
Important: These are the instructions for setting up your Star TSP143LAN on a Mac computer. Click the links here if you are using. Before getting started: Before getting started, it's a good idea to test out the printer. We'll also need the test receipts for setting up the printer. To perform a hardware self test on your printer:. Turn it OFF.
Hold the feed button down and turn the power back ON at the same time. Release the feed button. This will print out two test receipts.
At the bottom of the second page, it will show 'Current IP Parameters Status'. Hang on to this page or make a note of the IP Address.
Note: Your IP address will be different to the one listed in the picture above. Downloading and installing the Star driver: First off, we need to download the latest printer drivers for your computer. This is specialised software that helps the printer run correctly on your computer. To get this head over to and fill out the details below: Product Type: Thermal Printer Family: TSP100 Printer Model: TSP100LAN Interface: Ethernet Operating System: Mac OS X Next select Drivers and pick the driver listed under Recommended to download.
When this download is completed, open the file to extract it. Checkpoint: Not sure where to find the download? Go to finder and select 'Downloads' from he left hand list. The download will also appear at the bottom of Google Chrome, click the arrow here and select show in folder.
Next, open the extracted folder and navigate to Mac - CUPS - Documents and double click the 'starcupsdrv' file. This will create a new folder.
Open this and and go to drivers. Double click the.pkg file here and follow the install guide instructions. Installing your Star Printer: Now that this is complete you'll need to install the printer on your Mac. Navigate to 'System Preferences' and open 'Printers and Scanners'.
Here, use the plus in the botton left corner and click “add printer or scanner”. This will open up a new window where you'll need to put in some information. Select IP along the top and follow the instructions below to fill out the form correctly: 1. Address: This is where you need to put in your printer's IP address.
To find this locate the IP Address field on your receipt print out: 2. Protocol: Select 'Line Printer Daemon - LPD' from the dropdown 3. Queue: Leave this blank 4.
Name: This is an optional field but if you'd like to customise the name of your receipt put it in here. Location: Leave this blank 6. Use: Pick 'Select Software.'
From the dropdown. This will open up a new window. Search for Star in the top right, locate 'Star TSP100 Cutter' and click OK. Once you've put in all this information click 'Add'.
Your printer should now be set up and ready to go! Printing on Vend with Star: Now that your Star is installed you can start using it to print your receipts in Vend.
To perform a test print:. Head over to the History tab and click on a sale. Click view receipt. Pick the receipt template you’d like to use and click 'print'. This will take you to the print preview screen. If the Star is not your default printer, click 'change' and select the printer from the list.
You will also want to untick headers and footers and set the paper size to 72mm - 2000mm. Note: If you set your paper size to 72mm - 2000mm without disabling headers and footers, the printer will not auto cut at the main receipt Once that's been changed you should be able to print out a receipt. Set up your Cash Drawer Once you've got the printer all set up, you can connect up the cash drawer. The cash drawer connects to your receipt printer, and is triggered to open when you finish a cash or cheque sale and the receipt is printed by the printer.
Tip: You can manually open the cash drawer by clicking Command + E if you are using the old Vend Sell Screen or by performing a test sale if you are using Register for Mac. To setup the Cash Drawer: 1. Plug the RJ12 connector cable (the one that looks similar to a phone line) from the cash drawer into the receipt printer. Head to the following URL:. This will take you to CUPS. CUPS is a network printing service used by Mac computers. It allows you to setup your printers on a network, and customise options such as cash drawer setup.
Recieve this screen? To learn how to enable CUPS for your computer. Once in CUPS, Select your printer model from the list below: 4.
Select from the drop down menu 'Set Default Options' 5. From here, select 'Cash Drawer Control', choose 'Open Drawer 1 and 2' under 'Cash Drawer' and click the 'Set Default Options' button below. Your cash drawer should now be all set to go! You can test it out by clicking Command + E on your keyboard when in the old Vend Sell Screen or by performing a test sale if you are using Register for Mac.
The Star TSP100III model connects wirelessly to your internet router and provides wireless receipt printing from your Windows computer. Setting up your Star TSP100III involves the following steps:. NOTE: Like the Star TSP100 model, the Star TSP100III can also provide wireless receipt printing by connecting directly to your internet router with an ethernet cord.
For more information on this LAN setup,. Connecting your printer. Connect the power cord to your printer and an electrical outlet. Turn on the printer and wait for the blue Ready light to become solid.
Inserting your paper roll. To open the printer's lid, push the latch on the right away from you and lift the lid upwards. Insert the paper roll in the orientation below. Pull the paper out past the cutter at the front of the printer.
Push the lid down to snap the latch shut. Connecting your printer to your wireless network The simplest way to connect your printer to your wireless network is. If your router does not support WPS, you can connect by the. Connect by WPS. On the back of your printer, press and hold the red PAIR button.
The blue Ready light in front of the printer will start blinking. On your router, press the WPS button. NOTE: Step 1 and 2 need to be done within 30 seconds of each other. Once the connection between your printer and router is established, the blue Ready light will be solid and your Network Configuration and Current IP Parameters Status will print automatically. NOTE: If a connection is not established after repeating steps 1-3, refer to Star Micronic's article.
Under Current IP Parameters Status, take note of the IP Address. This is your printer's new dynamic IP address. Connect by AP network mode Connecting your printer to your computer by the AP network mode involves:.
1. Printing your Network Configuration and Current IP Parameters. To turn off your printer, press the power switch on the left. While your printer is off, press and hold the FEED button on the front of your printer. Still holding the FEED button, turn on your printer using the same power switch. Once your Network Configuration and Current IP Parameters Status print successfully, release the FEED button.
Under Network Configuration, take note of the SSID. This is you printer's name. Under Current IP Parameters Status, take note of the IP Address. This is your printer's default static IP address. Setting your wireless LAN settings. From your Network Settings, select your. Click Connect.
From your Firefox browser, enter your printer's. From the left menu, click Login. In the new Authentication Required window, enter the following:. User Name: root. Password: public. Click OK. To close the new security window, click Cancel.
From the left menu, click WLAN Settings. Select Infrastructure Mode and enter the following:. SSID: your Wi-Fi network's name. Security: WPA2/AES. Security Key: your Wi-Fi network's password.
Click Submit. From the left menu, click the Save section and select the following:. select Save Configuration printing Restart device. click Execute. From the automatic printout, Under Current IP Parameters Status, take note of the IP Address. This is your printer's new dynamic IP address. Installing your printer driver on your computer.
For Windows 7 and later, to initiate the download of your printer driver to your computer. To save your printer driver, click OK. From your browser's Downloads folder, double-click your tsp100 file to locate it in your computer. From the tsp100 folder, double-click Autorun. From the Compressed (Zipped) Folders windows, click Extract All Extrac t. From the tsp100 folder, double-click Autorun. From the new TSP100 futurePRNT window, click Installation I Accept.
From the new User Account Control window, click Yes. From the new Install Shield Wizard window, click Next Next Next Install. Deselect the Launch Star Cloud Services Web site and click Finish.
Adding your printer to your computer. To open your LAN & Bluetooth Setup Tool, search for LAN in the bottom left search field of your screen.
Click LAN & Bluetooth Setup Tool. From the new User Account Control window, click Yes. In the new LAN & Bluetooth Setup Tool window, click Discovery. Once your Star TSP100III and it's dynamic IP address is listed, highlight your printer and click Print Queue. From the new Print Queue window, select the Print Test checkbox and click Apply. Formatting your computer settings.
Go to Start Control Panels View devices and printers. NOTE: If you are using a Windows 8 or 10 version, right-click the Start Menu instead of doing a left-click. Right-click the Star TSP100III and select Printing Preferences. Click the Advanced button and set the P aper Size to 72 x Receipt. Click OK OK. Right-click the Star TSP100III and select Printer properties.
Setting Up Pairing The Star Tsp100 Lan For Mac Free
Click Preferences Advanced and set the paper size to 72 x Receipt. Click OK OK. Click the Advanced tab. Click Printing Defaults and set the paper size to 72 x Receipt.
Click OK OK. Click the Device Settings tab and set the following:. FRICTION: 72 x Receipt.
Page Cut Type: Partial Cut (for receipts to cut automatically). Document Cut Type: Partial Cut (for receipts to cut automatically). Peripheral Unit Type: Cash Drawer (for the cash drawer to open when you print a receipt). Peripheral Unit 1: Document Top (for the cash drawer to open when you print a receipt). Peripheral Unit 2: Document Top (for the cash drawer to open when you print a receipt). Right-click the Star TSP100III and select Default Printer (optional). Ensure that the green checkmark appears next to the printer. Formatting your Firefox browser settings Formatting your Firefox browser settings involves configuring the:.
A bout:config settings. Open your Firefox browser. In the address bar, enter about:config. Click the I accept the risk! button. In the Search bar, enter margin.
From the Preference Names below, double-click their Value columns enter 0 click OK. print.printmarginbottom. print.printmarginleft.
print.printmarginright. print.printmargintop. print.printunwriteablemarginbottom. print.printunwriteablemarginleft.
print.printunwriteablemarginright. print.printunwriteablemargintop NOTE: If you have Preference Names for margins specific to your Star TSP100III printer, change them to 0 as well. In the Search bar, enter header.
From the Preference Names below, double-click their Value columns delete the values click OK:. print.printheaderleft. print.printheaderright NOTE: If you have Preference Names for headers specific to your Star TSP100III printer, change them to 0 as well. In the Search bar, enter footer. From the Preference Names below, double-click their Value columns delete the values click OK:.
print.printfooterleft. print.printfooterright NOTE: If you have Preference Names for footers specific to your Star TSP100III printer, change them to 0 as well.
In the Search bar, enter printprinter. From the Preference Name printprinter, right click its Value column click Reset. From the Search bar, enter print.saveprintsettings. If you print from Firefox to multiple printers, from the Preference Name print.saveprintsettings, double-click the Value column to set it to false instead. Close the about:config Firefox tab.
Page setup. Open your Firefox browser. Click File Page Setup. Click the Margins & Header/Footer tab.
In the Margins section, enter 0 in all the fields. In the Headers & Footers section, select blank from all the drop-downs. Print prompt properties. From the main menu of your Retail account, click Reports Totals. From the ID column, click a blue Transaction ID. Click the grey Print Receipt button. From the new Print window, click Properties.
From the new Properties window, click Advanced. From the new Advanced Options window, make sure the Page Size drop-down menu is set to 72mm x Receipt.
Click OK OK OK. You should have a successful receipt and your computer should be official setup for wireless receipt printing!